How To Remove Front Panel Of Ge Stackable Washer
GE Washer Disassembly Guide
One of the about challenging things about do-it-yourself appliance repair is dissembling the appliance to make the repairs. Luckily this GE washer disassembly guide will walk you through this procedure step-by-pace. And then you can utilise my repair guide to diagnose the problem and my GE washer disassembly guide to assistance you replace the part.
If yous need a part Yous tin enter your model number or office number here to search the part you lot demand.
Should you have to remove the spin basket/tub to complete the repair you will need a spanner wrench. The spanner wrench made past GE is around $50, which is very expensive if y'all only program to use it once. Hither is a link to a spanner wrench that is much cheaper that will work for GE washers.
Also see my GE washer disassembly video at the bottom of this page.
Top and front removal
1. Remove the forepart past pushing a butter knife (or anything apartment, I usually utilize my truck keys) between the meridian and the front in line with the grove in the lid as shown.
2. Remove the ¼ inch screws that hold the elevation on.
3. Remove the peak. Note that you take to remove the lid switch if your washer has a magnetic hat switch and if information technology has a mechanical lid switch you must unplug information technology.
Agitator Removal
In this department of this GE washer disassembly guide I volition walk you through the steps in disassembling the to replace the agitator-coupling.
one. The agitator just lifts straight up and out. Note that information technology may be difficult simply if you tin get your fingers nether it and stone information technology back and forth it will sideslip up. Also note that if y'all are unable to go your fingers under it you can skid a belt under it and pull from the chugalug.
two. Nether the agitator you should meet the anarchist-coupling, remove information technology using a 7/sixteen socket.
Spin Basket Removal/Tub seal Replacement
In this section of this GE washer disassembly guide I will walk you through the steps in disassembling the to replace the tub seal.
1. Follow steps in meridian and front removal and anarchist removal.
ii. Side by side remove the four 5/16 screws that agree the damping straps on.
iii. Unhook the drain hose on the bottom of the tub.
4. Unhook the pocket-sized water level tube on the left hand side.
5. Unplug the motor and remove the ground screw.
6. Lift upwardly on the tub and unhook all four of the suspension rods
7. Elevator upward on the whole unit and bring it out of the case bottom offset every bit shown.
viii. Remove the cover off of the tub equally shown. Notation be careful not to over bend the tabs or it may not snap back in place.
Buy appliance parts online and save.
9. Remove the left-handed one-11/16 hub nut. Note that the tool shown is a spanner wrench designed for removing this nut and the part number is WX5X1325. Likewise annotation that you may be able to remove this nut using a wrench but typically they are as well long and so if you have to buy a tool to remove this nut, buy the ane I draw higher up.
Should you have to remove the spin handbasket/tub to complete the repair you will demand a spanner wrench. The spanner wrench made past GE is around $50, which is very expensive if y'all only programme to utilise it once. Here is a link to a spanner wrench that is much cheaper that will work for GE washers.
Cheaper Spanner Wrench For GE washers
10. Lift the spin basket up and out of the tub.
11. Remove the divide band. Annotation this carve up ring volition suspension easily, so be careful.
12. Remove the hub washer.
Note that at this point in GE washer disassembly you can supercede the tub seal. Just utilise a screwdriver to prize the old one out. Then tap the new 1 in with a edgeless object such as a nut driver with out a socket making sure it is seated practiced.
Transmission Removal
In this section of this GE washer disassembly guide I volition walk you through the steps in disassembling the to replace the transmission.
ane. Follow steps in Elevation and front removal, agitator removal and spin basket removal.
2. Turn the unit over as shown.
iii. Remove the ¾ basics belongings the transmission caster on. Note that yous accept to somehow finish the pulley from turning in social club to remove the nut. They make a special tool for this but I do it the fashion shown without the tool. Besides y'all can also agree the belt by manus.
four. Remove the four 3/viii screws that concur the transmission to the to the platform.
5. Remove the ½ inch screws that hold the platform to the tub.
6. Lift the platform up and off of the transmission.
seven. Lift the transmission upward and out of the tub.
8. Using a long screwdriver knock the erstwhile tub seal out from the bottom of the tub.
Motor and clutch removal
1. Remove the front as shown in the starting time step in front and top removal.
2. Remove the 3/8-inch nuts under the motor.
3. Turn the transmission to permit you to lean the motor back and slide it out.
4. To remove the clutch (not on newer models) turn the motor over and remove the clip that holds the clutch on.
5. Lift the clutch up and off the motor shaft.
Return From GE Washer Disassembly Guide
Source: http://www.appliance-repair-it.com/GE-washer-disassembly.html
0 Response to "How To Remove Front Panel Of Ge Stackable Washer"
Post a Comment